2020-09-14 20:02
聚乙稀塑料儲罐軟化變形應該如何來解決
在解決聚乙稀塑料儲罐軟化變形整個問題前,我們要先知道一些聚乙稀塑料儲罐的產品功能,聚乙稀塑料儲罐適用塑料的較小軟化點為108℃,較大崩碎點為-70℃,所以咧通常情況可使用于盛放溫度-40℃至60℃的液體。若盛放液體密度過重或溫度大于60℃時,應選取鋼襯塑防腐儲罐,防范聚乙稀塑料儲罐儲罐軟化變形。若聚乙稀塑料儲罐使用于化學反應或稀釋?zhuān)褂们皯鰧脑囼?,測出反應或稀釋較高溫度。
1、聚乙稀塑料儲罐選取滾塑工藝成形。
2、生產的聚乙稀塑料儲罐的原料為滾塑產品專門料——線性低密度聚乙稀(LLDPE)或線性中密度聚乙稀(LMDPE)。聚乙稀塑料儲罐可以盛放常溫狀態下的無機酸、堿、鹽大多數化學物質及很多有機化合物。
3、聚乙稀塑料儲罐適用塑料的較小軟化點為108℃,較大崩碎點為-70℃,所以咧通常情況可使用于盛放溫度-40℃至60℃的液體。若盛放液體密度過重或溫度大于60℃時,應選取鋼襯塑防腐儲罐,防范儲罐軟化變形。若聚乙稀塑料儲罐使用于化學反應或稀釋?zhuān)褂们皯鰧脑囼?,測出反應或稀釋較高溫度。
4、聚乙稀塑料儲罐罐體上的進料口、出料口、液位計口、法蘭等均為整體一次成形無焊接,不需配換進出料口。在盛放酸堿性化學物質時,要配備耐酸堿墊圈。在盛放有機化合物(尤其是有機溶液)時,配備不容易溶解的橡膠密封墊。
5、聚乙稀塑料儲罐設備不太適合盛放強氧化劑(如溫度60℃時,濃度75%以上的硫酸,30%以上的濃硝酸等)及優良的有機溶液(苯類、醚類、酮類、酯類)等。
大名县|
上蔡县|
保德县|
义乌市|
苍梧县|
温州市|
睢宁县|
来凤县|
赣州市|
庄河市|
台东县|
德化县|
宝清县|
吉水县|
台东市|
南阳市|
延川县|
丹凤县|
邵东县|
洪湖市|
长海县|
晋州市|
巴里|
成武县|
阿荣旗|
平远县|
井研县|
万源市|
高尔夫|
江达县|
观塘区|
黄山市|
石渠县|
楚雄市|
丽水市|
临夏县|
巴马|
台北县|
鞍山市|
江油市|
龙岩市|
http://444
http://444
http://444
http://444
http://444
http://444