2021-01-12 15:41
關于熱水壓力水柜構造和原材料以及裝配工藝的
一、熱水壓力水柜構造規定
1、成套設備壓力水柜應包含液位儀表、閥門、氣體截止閥門、洩放閥、壓力表和壓力汽車繼電器,這種零配件應合乎船舶規定。
2、熱水壓力水柜的內徑大于或等于700Mm時,應設手孔。環形手孔的直徑不可低于400mm,腰環形手孔規格不可低于300mmx400Mm。
3、熱水壓力水柜應設立保險裝置,保險裝置的打開壓力應超過工作中壓力,低于設計方案壓力。
4、熱水壓力水柜的進出口貿易聯接法蘭盤技術標準和規格應合乎GB573或GB2506的規定。
5、熱水壓力水柜的本身應能承擔1.5倍的設計方案壓力,而無毀壞和顯著形變。拼裝后成套設備的熱水壓力水柜在1.25倍的設計方案壓力下做密性實驗應不漏水。
二、熱水壓力水柜生產制造規定
1、筒體、簡體應以機械設備冷拉或熱處理成形,但不可應用捶擊成形。筒體選用壓合成形時,不可造成粗晶狀況。
2、熱水壓力水柜簡體同心度就是指同-橫截面上所測很大內徑和較小內徑之差,應不超該橫截面設計方案內徑的1%。
3、熱水壓力水柜筒體成形后的較小壁厚不可低于設計方案薄厚的90%。
4、簡體生產時,須避免造成簡體邊沿傾斜、甩尾、錐型鼓型等缺點。裝配工藝后熱水壓力水柜簡體平行度每米長短內不可超出1.5毫米,總長不可超出3毫米。
三、熱水壓力水柜原材料規定
熱水壓力水柜的本身及人孔蓋原材料均應選用鎮靜鋼,不銹鋼板材的技術標準應合乎GB712規范中B級的要求。原料進廠檢測應按ZBU41005的規定。
四、熱水壓力水柜裝配工藝規定
1、熱水壓力水柜的壓力汽車繼電器應能確保在要求的底壓/髙壓下自動啟動/終止供離心水泵,考慮全自動供電的效率。
2、熱水壓力水柜的本身抗壓強度實驗合格后,內表面應防銹處理拋光,隨后涂上無毒性環氧涂料。
3、熱水壓力水柜抗壓強度實驗和密性實驗合格后,外表面應防銹處理,并涂防銹處理面漆和深灰色油漆。
阿拉善盟|
苏州市|
长春市|
莱芜市|
宁武县|
吴江市|
保康县|
许昌市|
六盘水市|
长葛市|
陇川县|
景洪市|
凤庆县|
大冶市|
林口县|
磐石市|
安塞县|
柏乡县|
崇左市|
南投县|
金华市|
磴口县|
阿克苏市|
托克逊县|
财经|
贵南县|
花莲县|
扶风县|
洛南县|
宁城县|
静海县|
佛学|
临漳县|
开化县|
容城县|
榕江县|
澳门|
苏尼特右旗|
阜南县|
龙井市|
冷水江市|
http://444
http://444
http://444
http://444
http://444
http://444