2021-01-12 16:22
海水壓力水柜的檢測試驗要注意哪些方面
一、海水壓力水柜外型查驗
查驗海水海水壓力水柜的外型、選料、配套設施件、規格等,查驗結果應合乎機械設備海水壓力水柜應包括液位儀表、閘閥、汽體截止閥門、洩放閥、壓力表和壓力繼電器,這類零配件應符合船只要求的規定。
二、海水壓力水柜焊縫檢測
a、電焊焊接試板檢測內容包含正彎試驗、反彎試驗、對接焊縫橫著抗拉力試驗、宏觀經濟試驗斷裂面機構查驗等。電焊焊接試板需作100%X射線檢查,評片按GB3323要求,焊縫川I級覺得合格。
a、商品的一條焊縫應作10%的X射線檢查。評片按GB3323要求,焊縫I級覺得合格。
a、當焊縫上發覺有不允許的缺點時,消除后容許維修,維修后應開展X射線拍片子。同一位置的維修頻次不適合超出2次。
三、海水壓力水柜抗壓強度試驗和密性試驗
a、海水壓力水柜本身做成并經檢測合格后,應開展抗壓強度試驗。試驗方式按GB11037開展,試驗結果應合乎開水海水壓力水柜的自身應能擔負1.5倍的方案設計壓力。
b、海水壓力水柜經抗壓強度試驗合格并在配件安裝后才可開展密性試驗。密性試驗用冷水為物質.試驗壓力為I.25倍的設計方案壓力。試驗時壓力應漸漸地升高,做到要求試驗壓力后保壓5min,隨后降至設計方案壓力,對全部焊縫和聯接位置開展泄露查驗,應合乎組裝后機械設備的開水海水壓力水柜在1.25倍的方案設計壓力下做密性試驗應不滲水規定。
四、壓力繼電器動作試驗
海水壓力水柜與水資源相連,在要求的低壓高壓下,觀查可否全自動供電和終止供電,其結果應符合規定。
五、海水壓力水柜閥門的開啟和回座試驗
海水壓力水柜密性試驗合格后,將閥門控制精度到規定值,開展打開和回座試驗。打開壓力超過工作中壓力而低于設計方案壓力,回座壓力為工.作壓力的0.85倍,持續試驗三次,應合乎安全裝置的開啟壓力應超出工作上壓力,小于方案設計壓力規定。
景德镇市|
抚顺县|
阿勒泰市|
淅川县|
甘泉县|
桂林市|
北海市|
三门县|
焦作市|
岑巩县|
绥化市|
全南县|
鹿泉市|
石台县|
方正县|
体育|
莲花县|
凤山市|
南汇区|
凤凰县|
高密市|
同心县|
外汇|
红安县|
绥宁县|
韩城市|
柳州市|
彰武县|
克什克腾旗|
漳州市|
抚顺县|
隆回县|
怀化市|
无锡市|
洪泽县|
孙吴县|
沭阳县|
阿拉善盟|
育儿|
固阳县|
孟连|
http://444
http://444
http://444
http://444
http://444
http://444