2021-01-18 15:50
冷凝器結垢后應該如何來處理
冷凝器結垢后,導熱熱阻增大,傳熱系數值減少,冷凝溫度與傳熱系數成反比,冷凝器溫度上升,冷凝壓力也相應增加,冷凝器結垢越嚴重,冷凝壓力就越顯著增加,壓縮機的功率增加,冷凝機的功耗增加,電力浪費保持冷凝器的清潔是非常重要的。
常見冷凝器的主要清洗方法如下:
一、物理清洗法。
機械除垢是用軟軸清洗管器或高壓射流清洗冷卻管冷凝器除垢的方法。
a、高壓水射流清洗。
“高壓水流”是指水由高壓水發生裝置加壓到數百個大氣壓,由帶有細孔徑的噴射裝置轉換成高速細小的“水流”。高壓水由專用噴嘴噴出,清洗管束,沖洗冷凝器管束中的水垢,恢復管束中的清潔度。
b、軟軸清洗管器清洗。
用軟軸清洗管器連接的傘型齒輪狀刀片在冷凝器的立管內從上到下旋轉滾動去除污垢,用循環冷卻水冷卻刀片和管壁摩擦產生的熱量,同時將去除的污垢和銹等污垢沖入池中。
在去除污垢的過程中,根據冷凝器的污垢厚度和管壁的銹蝕程度和使用壽命來決定選擇合適直徑的滾筒。然而,在一次去除污垢的滾筒直徑小于冷卻管的內徑。為了不損壞管壁,選擇與冷卻管內徑相似的滾筒進行二次去除污垢。
該機械去除污垢的方法是利用傘型齒輪狀滾筒在冷卻管內旋轉進刀過程中的滾筒旋轉和振動,去除冷凝器冷卻管中的污垢和污銹等,去除污垢后,去除冷凝池中的水,從池底清除去除的污垢、銹等污垢,再次注入水。
機械清洗面對硬垢時清洗時間長,不徹底,容易損傷冷凝器管束,清洗后預膜效果差,管束腐蝕問題。
二、化學酸洗去垢法。
用調制的弱酸性除垢劑清洗冷凝器,脫落水垢,提高冷凝器的傳熱效率。
操作方法如下:
在酸洗槽中配制除垢液,啟動酸洗泵,使除垢液在冷凝器冷凝管中循環24小時,一般24小時后基本除垢。
停止酸洗泵工作后,用圓鋼刷在冷凝管器的管壁內往返刷,用清水清洗污垢和銹。
用清水反復清洗管內殘留的除垢劑溶液,直到完全清潔為止。
化學清洗對藥劑濃度控制有很高的要求,濃度過低不能清洗污垢,濃度過高會(huì )腐蝕冷凝器管束,而且清洗過程中需要用大量的水清洗系統中的藥劑,這部分污水不能直接排出,處理完畢后排出
张掖市|
章丘市|
观塘区|
安远县|
淮滨县|
丰台区|
岳普湖县|
德安县|
厦门市|
洛阳市|
常宁市|
滁州市|
霸州市|
奈曼旗|
天全县|
城步|
芒康县|
阿瓦提县|
锡林郭勒盟|
洪湖市|
崇左市|
柘荣县|
顺义区|
年辖:市辖区|
永胜县|
天门市|
文昌市|
晋宁县|
财经|
富顺县|
大渡口区|
普洱|
平远县|
商南县|
博客|
紫金县|
抚宁县|
朝阳县|
修武县|
炉霍县|
固始县|
http://444
http://444
http://444
http://444
http://444
http://444